Skid Steer Landscaping & 
Earth Moving Attachments


 Tree & Root Puller

Skid Steer Tree and Root Puller

Features

  • 3" x 8" hydraulic cylinder and hoses
  • Flat faced couplers included
  • 3000 PSI recommended
  • Heavy duty frame
  • Reinforced heavy duty universal mounting brackets
  • Teeth are constructed from T1 steel
  • Pulls 5” to 8” trees, roots and posts
Depth        
Width        
Height       
Weight    
35 inches
45 inches
20 inches
425 #


**Weights and measurements are approximate


 

 Post Hole Auger

Skid Steer Post Hole Auger

Features

  • Hydraulic (orbit) drive unit – low speed / high torque (med. flow)
  • Auger Digs 4 ½ to 5 feet deep without extensions
  • Direct drive – no chains
  • 2” output round shaft, hex shafts available too
  • Post Hole Auger has reinforced heavy duty universal mounting brackets
  • Recommended 15 – 20 GPM
  • Augers available in 6”, 9”, 12”, 15”, 18” and 24” (sold separately)
  • Extra large auger bits available by request
Length       
Width        
Height      
Weight    
45 inches
46 inches
19 inches
280 #


**Weights and measurements are approximate


 Brush Devil Mower & Brush Cutter

Skid Steer Mower

Features

  • The Brush Devil mower & brush cutter cuts small trees, brush and grass
  • Brush Cutter comes complete with heavy duty gear box
  • Powered by Parker motor
  • Torque at 3000 PSI
  • Requires 15 to 21 GPM
  • Replaceable heat-treated updraft blades
  • Front and rear chain guards
  • Reinforced heavy duty universal mounting brackets
  • Flat Faced hydraulic couplers included
  • Optional gauge wheel available
Width        
Length       
Weight    
60 inches
78 inches
745 #
72 inches90 inches935 #


**Weights and measurements are approximate



 

 Leveling Bar

Skid Steer Leveling Bar

Features

  • Constructed from two ½” x 6” hardened cutting edges (one in front and one in back of the leveling bar)
  • Frame constructed with 2”x 4” and 2”x 2” ¼” tubing
  • 2 ½” 2 ½” x 3/8” angle iron is welded in the center, 1” higher than the cutting edge which allows the dirt to roll
  • Step is welded on for easy access
  • Reinforced heavy duty universal mounting brackets
  • Lift tabs (3/8” angles on top) are welded on frame so the attachment can be easily moved or carried with a bucket
  • Ideal for landscaping, driveways, parking lots and concrete work
  • Custom width units are available
Width        Depth        
Height       
Weight    
78 inches
48 inches
24 inches
510 #


**Weights and measurements are approximate


 Big Ripper Shovel with Teeth

Big Ripper Shovel

Features

  • Includes three replaceable ripper teeth
  • Ripper teeth are 6” long
  • Reinforced heavy duty universal mounting brackets
  • Half moon plasma cut end plates made from ½” plate steel
  • Ideal for roots, stumps, trenching and boulders
  
Depth        
Width        
Height       
Weight    
47 inches
45 inches
20 inches
335 #


**Weights and measurements are approximate


 

 U-Blade

Skid Steer U Blade

Feautres

  • Main frame is constructed of 1/4”  2”x 2”  wall tubing
  • Grade 50 plate steel for longer life
  • Universal plates 5/16” thick welded on the frame
  • The U-Blade is made of 1/2” thick steel and is beveled on the front and back for two way digging – forward and backward
  • Ideal for transplanting trees, trenching, lifting out rocks or stumps
  • Blade diameter measures 26 inches
Depth        
Width        
Height       
Weight    
58 inches
45 inches
28 inches
340 #


**Weights and measurements are approximate


 Backhoe

Skid Steer Backhoe

Features

  • 20” bucket with four teeth
  • Grease-able heavy duty pins
  • Requires a minimum 65 HP
  • Equipped with a 3” x 16” hydraulic cylinder, hoses and couplers
  • Bucket wall is ¼” plate steel; bottom is ½” plate steel
  • Digs up to 7 ½ feet deep
  • Reinforced heavy duty universal mounting brackets; gusseted top and bottom for extra strength
  • 10” bucket also available
Length       
Width        
Height       
Weight    
85 inches
48 inches
22 inches
645 #


**Weights and measurements are approximate


 

 Big Ripper Grapple

Skid Steer Big Ripper Grapple Bucket

Features

  • Includes three replaceable ripper teeth
  • Ripper teeth are 6” long
  • Constructed of two sleeved 24” conus tines
  • Single hydraulic cylinder
  • Reinforced heavy duty universal mounting brackets
  • Half moon plasma cut end plates made from ½” plate steel
  • Includes flat faced couplers and hoses with built in orifices
  • Ideal for stumps, rocks and brush
Depth        Width        Height       
Height - Open    Weight    
36 inches32 inches34 inches44 inches475 #


**Weights and measurements are approximate

  Skid Steer 6-Way Dozer Blade

Skid Steer 6-Way Dozer Blade
X-treme Skid Steer 6-Way & 4-Way Dozer Blade Attachment Specs

The CID 6-way & 4-way dozer blade comes with an electric over hydraulic valve to operate the tilt function of the blade. Only one set of auxiliary hydraulics are needed. Optional universal, 8 pin or 14 pin wiring harness are available.

  • Electric over hydraulic valve

  • Replaceable cutting edge is available

  • Available Sizes: 72″, 84”, 96”

  • Wire harness included

  • 3/16″ mold board

  • 3 1/2″ x 4″ cylinders

  • 1/2″ edge

  • Optional universal, 8 pin or 14 pin wiring harness

  • Optional 4-way dozer blade available

 

 Design

Skid Steer 6-Way Dozer Blade

Our X-treme Skid Steer 6-Way & 4-Way Dozer Blade Attachment is an excellent tool for grading. Easily cut a road, level ground for building, or cut a ditch. The dozer blade attachment can push and move large amounts of material quick and easy. Typical use of the 6-way dozer include back-filling, creating storm water run off grades or sculpting landscape area. The 6-way dozer blade works great on material like sand, gravel, or loose dirt. The skid steek 6-way & 4-way dozer blade attachment requires 4 hydraulic functions to be a true 6-way unit. It has the normal lift and curl. Right and left angle. Right and left side up and down tilt.



 

 Dirt Bucket

Skid Steer Loader Dirt Bucket

Features

  • Dirt Bucket constructed of ¼” plate steel with ¾” x 6” Cutting Edge weld on (bolt on options also available)
  • ½” x 4” wear plates on bottom for extra strength
  • Dirt Bucket has reinforced heavy duty universal mounting brackets; gusseted top and bottom for extra strength


Width        Depth         Height         Weight    
60 inches37 inches22 inches470 #
66 inches37 inches22 inches515 #
68 inches37 inches22 inches540 #
72 inches37 inches22 inches560 #
80 inches37 inches22 inches625 #
84 inches37 inches22 inches645 #

**Weights and measurements are approximate


 
 
Cornerstone Industries specializes in telehandler and forklift attachments. Based in Brandon, South Dakota we provide quality Work Platforms, Man Baskets, 180 Degree Swing Carriages, Buckets & Grapples, Jibs, Forks, Carriages, Remote Controls, and many Specialty Attachments. Cornertone is also your source for a full line of scaffolding and scaffolding accessories.

Website Designed and hosted by The Gage Team.